|
Get the Flash Player to see this player.
DESCRIPTION
Eurothane is a modern urethane varnish with the appearance of a traditional alkyd formulation.
Eurothane resists yellowing, and does not possess the “plastic” appearance common to may urethanes.
Eurothane Varnish is easy to apply and dries to a hard finish protecting wood against
abrasion, alcohol and water. This formulation results in an elastic and durable finish and is compatible
with most modern urethane or traditional varnishes. We suggest that when applying
this varnish over an existing finish, test it for compatibility on a small, unobtrusive area before
proceeding with the work.
Eurothane is clear and colorless. It is available in High Gloss, Satin and Matte finishes, all intermixable
to achieve any intermediate level of gloss desired. Similar to other finishes, High Gloss
provides the hardest and most durable film. Satin provides a low-luster, hand-rubbed appearance,
while Matte virtually “disappears” due to its non-reflective quality.
SURFACE PREPARATION
Surfaces to be varnished should be dry, free of dust, chalk, grease and any foreign material which
would affect adhesion.
Dust and chalk, etc should be eliminated.
Remove grease and wax with denatured alcohol.
Sound, previously varnished surfaces must be dulled by light sanding.
APPLICATION
Tools: Use a first quality, clean natural bristle
brush, or lambswool applicator for floors (we
recommend the Omega Small Flats, S57’s, or
the Omega Large Full Oval, S55-2).
NEVER use a brush for varnishing if it has
been used previously for painting.
New woodwork and floors: After surface
preparation (sanding, etc.) and cleaning,
wipe down surface with a clean cloth
impregnated with denatured alcohol.
Apply three coats of Eurothane Varnish,
allowing twenty four hours drying time
between coats.
Surface should be lightly sanded with very fine sand paper (we recommend 600 grit silicon carbide wet/dry paper that is lubricated with mineral spirits) and tacked
between coats. To ensure maximum durability
of Eurothane Satin and Matte finish, apply two
coats of Eurothane High Gloss before applying
the finish coat of Satin
or Matte.
On previously varnished surfaces:
Varnished surfaces which are sound should
be sanded, cleaned thoroughly and wiped
down with a clean cloth impregnated with
denatured alcohol. Apply two or more coats
of Eurothane, allowing twenty-four hours of
drying time between coats. Surface should
be lightly sanded with fine paper – 220 grit – and tacked between coats. To ensure
maximum durability of Eurothane Satin or
Matte finish, apply two coats of Eurothane
High Gloss before applying the finish coat
of Satin or Matte.
On previously varnished surfaces
in extremely poor condition: It is
recommended that the old varnish be
removed completely by abrasion, and
then proceed as for new wood.
Work area should always be well ventilated.
NEVER shake container. To avoid bubbles
varnish should be STIRRED ONLY.
For floors, we recommend a MINIMUM of
three coats, with the first two in High Gloss
for maximum durability. Final coat should
be High Gloss or Satin.
NOTE: The surface drying time of
Eurothane Varnish is rather quick, so it is
very important to apply thin, even coats,
especially for flooring.
*EXTERIOR USE OF EUROTHANE
Eurothane Satin Varnish is suitable for exterior
use as a finish coat over an FPE Marine Yacht
Varnish System. (Not for exterior decks.)
MAINTENANCE
Easy to clean. Wash (scrub if necessary) with a
weak solution of mild powdered detergent
and cold water; rinse and dry (buff) to avoid
water spots. Do not use liquid household
cleaners or harsh detergents as they will dull
the surface.
PACKAGING/COVERAGE
.75L container covers 120 square feet
2.5L container covers 400 square feet
STORAGE
Almost unlimited in original unopened containers.
TECHNICAL SPECIFICATIONS
Binder: Long-oil urethane modified
alkyd resin
Solvent: White Spirits
Clean up: FPE Mineral Spirits
Specific gravity: 0.90
Solids contents:
High Gloss Satin Matte
• by weight 42.5 44 46
• by volume 33 35 37
Viscosity (emila rot. visc. meter) in Dpas/20°C:
1.0 -2.0
Specular gloss
• High Gloss (60°): 90
• Satin (60°): 20
• Matte (85°): 8
Recommended film thickness:
• wet: 60 – 70 microns/coat
• dry: 20 -25 microns /coat
Drying time: 2 to 4 hours tack free
24 hours recoatable
VOC: High Gloss: 494 g/l
Satin: 485 g/l
Matte: 475 g/l
* Under normal environmental conditions, this product requires no thinning. Clean up with FPE Mineral Spirits. |